Neo-Neon Elektor-Flex ultra slim per 1m in blue

Elektor-Flex ultra slim neon per 1m

Low voltage, low energy, Elektor-Flex is a flexible neon replacement which gives high, even brightness, making it ideal for the construction of stunning, eye catching signs, without the worries of high voltage and maintenance headaches of traditional neon signs.

Elektor-Flex ultra slim flexible neon is available in a roll of up to 50m and can be cut to size and sold per metre. A choice of six colours, amber, blue, green, red, white or yellow, enable Elektor-FLEX to enhance the aesthetics of any environment.

Elektor-Flex is powered by Neo-Neon DC power supply units, The type of power supply depends on the length of Elektor-Flex you require, so please contact our staff for advice if you need any assistance.

Elektor-FLEX - safety

Elektor-Flex tubes MUST only be cut on the indicated mark. Before connecting Elektor-Flex with connectors, bend the tube rightwards and leftwards, cut extra copper wires as needed, using the correct tools. Play close attention to polarity, when connecting two pieces. Do NOT use Elektor-Flex if there is any damage on the encapsulating jacket or to its cord, inspect periodically. Do NOT submerge in liquids. Do NOT secure Elektor-Flex oor its cord with staples, nails or by any means which may damage the insulation. Do NOT subject it to continuous flexing.

Warning - when using Elektor-FLEX outdoors always use proprietory portable lighting products. Basic safety precautions should be followed to reduce the risk of fire, electric shock and personal injury. Residential Current Circuit Breaker (RCD) protection should be provided on the circuit or outlet to be used for Elektor-Flex.

Elektor-FLEX choices

Elektor-Flex is offered in four versions giving full flexibility to lighting design.

Sleeved Elektor-Flex - projects light directionally upward and is recommended for larger forward facing buildings features and signs. Also available in ultra slim.

Unsleeved Elektor-Flex (NK) beams light halo fashion and is best suited for back lighting, cornice and effect lighting.

Elektor-Flex Mini - halo beam and high flexibility, ideal for signage and feature applications.

Elektor-Flex DMX - architectural high-impact 16.7 million linear colour change applications.

Power supply units

You will need a power supply unit (PSU) with Elektor-Flex (single colours):

50 Watt 24V DC switch mode power supply unit (SWS50W24) can run 12m of blue or white flex, or 7m of red, amber, yellow or green
75 Watt 24V DC switch mode power supply unit (SWS75W24) can run 18m of blue or white flex, or 10m of red, amber, yellow or green
100 Watt 24V DC switch mode power supply unit (SWS100W24) can run 25m of blue or white flex, or 14m of red, amber, yellow or green
150 Watt 24V DC switch mode power supply unit (SWS150W24) can run 37m of blue or white flex, or 21m of red, amber, yellow or green

Please note that the maximum run in one length is 40m, if you require longer lengths than you can run them off of the same power supply but they have to be separate.

300 watt and 600 watt power supply units are available, (SWS300W24) (SWS600W24), but please note if you do use a 600 Watt PSU you MUST split the load and MUST FUSE each section.

Other power supply units are available:

24V - 12 watt switch mode psu (SLS/PS/24/12) which runs 3m of blue or white flex, or 1m of red, amber, yellow or green.
24V - 24 watt switch mode psu (SLS/PS/24/24) which runs 6m of blue or white flex, or 3m of red, amber, yellow or green.
24V - 185 watt switch mode psu (SLS/24/225) which runs 46m of blue or white flex, or 26m of red, amber, yellow or green.

Please bear in mind 40m run is max you can run off a psu, if you require longer lengths than you can run them off of the same power supply but they have to be separate.

Power supply units for RGB Elektor-Flex:

EO-SRC171 Interior 3 channel DMX controlled psu 3 x 120w runs 15m of flex
EO-SRC181-24v Exterior 3 channel DMX controlled 3 x 120w runs 15m of flex
AUD-MD-CCH DMX modulator (requireds 24v DC PSU) 3 x 18w runs 2m of flex

Please contact our sales department for specialist advice on power supply units, end caps, splice connectors and other accessories you will need for your Elektor-Flex.

Page last updated:  Friday 25 July 2008

LED neon flex lighting main page

Full Wedgwood product list with over 10,000 audio visual products

E. & O.E. www.wedgwood-group.com

How to order from Wedgwood

Payment options: bank transfer, cheque, debit card, credit card, 14 and 30 day credit accounts (see below).
No credit card surcharges.

Wedgwood only deliver to the UK mainland. To place an order then please fax your official purchase order to 0800 018 9968 (or 01754 768036), including your purchase order number, invoice/delivery address, goods, delivery charge, total including VAT and method of payment. We are unable to take telephone orders, but you can order online with our shopping cart.

If you are an educational establishment, government establishment, large registered charity or blue chip company and wish to pay by 14 or 30 day account please fax your official purchase order.

Please do not book installation of equipment before goods have arrived and have been fully tested. We accept no liability for installation or other cost occurred in the case of late delivery. Courier delays, manufacturer supply problems, etc, are beyond our responsible control.

Copyright © Wedgwood AV Ltd 1996-2007