Neo-Neon Elektor-Flex Crystal RGB LED per 1m
Elektor-Flex Crystal LED neon flex - per 1m RGB Low voltage, low energy, Elektor-Flex is a flexible neon replacement which gives high, even brightness, making it ideal for the construction of stunning, eye catching signs, without the worries of high voltage and maintenance headaches of traditional neon signs. Dimensions 20x26mm, 72 LEDs per metre, 9.4w per metre, 24volts, RGB colour, LED life, white up to 50,000 hours, colours up to 100,000 hours. Max loading 480w PSU (power supply unit); 50m with SRC171 24v controlled. Elektor-Flex is powered by Neo-Neon DC power supply units, sold separately. The type of power supply depends on the length of Elektor-Flex you require, so please contact our staff for advice if you need any assistance. Colour changing controlled by DMX. Picture shows the single colours of Elektor-Flex Crystal for illustration only, and the effect of RGB on coving. Elektor-Flex Crystal uses the same LED technology as Elektor-Flex but comes in a transparent crystal tube giving 16.7 million RGB DMX controllable colour changing. Ekektor-Flex Crystal is ideal in subtler applications such as cove lighting or wall washes and is suitable for both interior and exterior linear lighting applications. Operating on 24V and consuming 2.88W per foot, Crystal emits little heat, requires minimum maintenance and an approx light life of up to 100,000 hours. It is encasulated in a purpose designed, white-walled, impact resistant jacket and is lightweight and weatherproof (weatherproof does not mean waterproof). Crystal can be cut, joined and easily shaped by hand, offering quick, low cost on-site installation. Elektor-Flex Crystal safety instructions Crystal tubes must only be cut on the indicated mark. Before connecting Crystal with connectors, bend the tube rightwards and leftwareds, cut extra copper wires as needed using the correct tools. Pay close attention to polarity, when connecting two pieces. Do not use Crystal if there is any damage on the encapsulating jacket or to its cord, inspect periodically. Do not submerge Crystal in liquids and do not secure on its cord with staples, nails or by any means which might damage the insulation, and do not subject it to continuous flexing. When using Crystal outdoors always use proprietory external lighting products for termination boxes etc. Basic safety precautions should be followed to reduce the risk of fire, electric shock and personal injury. Residual Current Cirucit Breaker (RCD) protection should be provided on the circuit or outlet to be used for Elektor-Flex Crystal. Elektor-Flex Crystal LED neon is available in a roll of up to 50m and can be cut to size and sold per metre in a choice of six colours, Red, Orange, Yellow, Green, White and Blue. RoHS and WEEE compliant.
You will need a power supply unit (PSU) with Elektor-Flex (single colours): 50 Watt 24V DC switch mode power supply unit (SWS50W24) can run 12m of blue or white flex, or 7m of red, amber, yellow or green Please note that the maximum run in one length is 40m, if you require longer lengths than you can run them off of the same power supply but they have to be separate. 300 watt and 600 watt power supply units are available, (SWS300W24) (SWS600W24), but please note if you do use a 600 Watt PSU you MUST split the load and MUST FUSE each section. Other power supply units are available: 24V - 12 watt switch mode psu (SLS/PS/24/12) which runs 3m of blue or white flex, or 1m of red, amber, yellow or green. Please bear in mind 40m run is max you can run off a psu, if you require longer lengths than you can run them off of the same power supply but they have to be separate. Power supply units for RGB Elektor-Flex: EO-SRC171 Interior 3 channel DMX controlled psu 3 x 120w runs 15m of flex Please contact our sales department for specialist advice on power supply units, end caps, splice connectors and other accessories you will need for your Elektor-Flex.
Page last updated: Friday 25 July 2008 LED neon flex lighting main page Full Wedgwood product list with over 10,000 audio visual products E. & O.E. www.wedgwood-group.com How to order from Wedgwood Please note that Wedgwood does NOT supply equipment to home users.Payment options: bank transfer, cheque, debit card, credit card, 14 and 30 day credit accounts (see below). Wedgwood only deliver to the UK mainland. To place an order then please fax your official purchase order to 0800 018 9968 (or 01754 768036), including your purchase order number, invoice/delivery address, goods, delivery charge, total including VAT and method of payment. We are unable to take telephone orders, but you can order online with our shopping cart. If you are an educational establishment, government establishment, large registered charity or blue chip company and wish to pay by 14 or 30 day account please fax your official purchase order. Please do not book installation of equipment before goods have arrived and have been fully tested. We accept no liability for installation or other cost occurred in the case of late delivery. Courier delays, manufacturer supply problems, etc, are beyond our responsible control. Copyright © Wedgwood AV Ltd 1996-2007
|
|||||||||||||||||||||||||||||||||||||||||||||||
|
